HYLATECHNIK SHOCK DAMPERS
 

Press
Products

Shock Dampers / Hyla-Lift / Parallel Control System 
Hydraulic Scrap Shear / Blank Holding System
Die Splitter Turnover Device / Ratio-Clamp
Hylatechnik Shock Dampers

 

Hylatechnik — Shock Dampers are designed to protect the press and tooling from server snap through loads.  The Hylatechnik dampers will reduce/eliminate:  reverse loads, floor vibration, noise and will increase tool life.  Applications include hydraulic presses, mechanical presses and press breaks.  The shock dampers are NOT limited to the press size.  They can be used on the largest of machines.

Click here to download Shock Damper Brochure (pdf - 1060 KB)
  Get Adobe Reader
 

Hyla-Lift
Hylatechnik — Hyla-Lift is a portable hydraulic die separator cart. The cart is used for die setting and die separation.  The four lifting cylinders have exact parallel motion even with unequal tool loads.  This allows the operator to break free the tool jam and lift the upper plate level.  The cart is available in three different lifting capacities, 10, 30, or 40 tons.  

Click here to download Hyla-Lift Brochure (pdf - 2013 KB)  
Get Adobe Reader

 

Parallel Control System

Hylatechnik — Parallel Control System for Hydraulic Presses. The parallelism equalizer system permits the use of tools with off center loads without the twisting of the ram to a non-permissible condition.  Press and tool life are increased and common use of cutting, drawing, trimming and contouring tools become possible. 

Click here to download Parallel Control System Brochure (pdf - 797 KB)  
Get Adobe Reader

 

Hydraulic Scrap Shear

 

Hylatechnik — Scrap Sheer is available as a freestanding unit or mounted directly to the press.  Power by a separate hydraulic power unit or use the hydraulics from the press.  Actuated controll, by either signal or hand/foot pedal switch.

Max width:                     40 inches

Max thickness:              0.394 inch

Max speed:                     150 spm  

Click here to download Hydraulic Scrap Shear Brochure (pdf - 530 KB)Get Adobe Reader

 

Hydraulic Blank Holding System

Hylatechnik — Hydraulic Blank Holding System is made up of individual pistons mounted in a manifold block or intermediate bolster.  The hydraulic blank holder provides the highest specific pressure in the smallest space.  A series of operations can be carried out in combination and the system will provide a consistent characteristic with each press stroke.  A solution for problem free drawing. 

Click here to download Hydraulic Blank Holding System Brochure (pdf - 530 KB)Get Adobe Reader
 

Die Splitter Turnover Device

 

AU — Die Splitter / Turnover Device is the ideal equipment for testing and spotting dies.  The up and down movement of the upper plate is driven through two ball bearing screws connected by two gear motors with two encoders for perfect synchronization.  The upper cross member can be rotated by 180° allowing work to be preformed quickly and safely.  The hydraulic power unit drives the rotation of the upper cross member and provides the power for the lower plate to slide out of the machinery.     

The parallels with “T” slots for die clamping of upper and lower tooling can be moved in order to install dies of different dimensions.  These parallels move easy on the ball bearings supports.  



Switch To Video Optimized For High-Speed Internet Connections.
* Video requires Windows Media Player 9 to view.

 

Ratio-Clamp®

Hänchen — Ratio-Clamp is a genuine safety clamping device, which unlocks hydraulically and in case of a power failure locks in any position mechanically.  The clamp can be used in any press related safety application and the clamping duration is maintained over an indefinite period without energy supplied.   

Click here to download Ratio-Clamp Brochure (pdf 5,900 KB)
Get Adobe Reader